Warner-electric AC10 Measuring System Manual do Utilizador Página 1

AC10 Measuring SystemInstallation InstructionsP-2012-2819-0402

10Warner Electric • 800-825-9050 P-2012-2 Electrical Installation(Read the entire electrical installation proce-dure before proceeding.)The PSAC10 Pow

11Warner Electric • 800-825-9050 P-2012-2J2 to W2 Tensioncell Connection with WarnerElectric supplied cableTerminal Label Description Wire ColorJ2-1 S

12Warner Electric • 800-825-9050 P-2012-2 The contact may be wired to function in eitherthe normally open or normally closed state.Terminal Label Desc

13Warner Electric • 800-825-9050 P-2012-2AC10 Setup ProcedureImportant: The input to any external devicewired to J6-3 Out1 or J6-1 Out 2 must be 10VDC

14Warner Electric • 800-825-9050 P-2012-2 7. Adjust Out 1 0% a. Connect a digital voltmeter between J6-3Out 1 and J6-4 Gnd. b. Press the UP or

15Warner Electric • 800-825-9050 P-2012-211.Adjust Out 2 100% a. Connect a digital voltmeter between J6-1Out 2 and J6-2 Gnd.b. Press the UP or DO

16Warner Electric • 800-825-9050 P-2012-2 TroubleshootingWhen properly installed in accordance with thedesign specification and procedures outlined in

17Warner Electric • 800-825-9050 P-2012-2a. Using an AC volt meter with at least5Khz band width, measure the voltagebetween J1-3 Exc and J1-4 Exc. The

18Warner Electric • 800-825-9050 P-2012-2 See Note3.132.133.441.135/8-11 UNC.93 Full Th’dfor MountingBoltElectricalConnector2.50.25 Dia. HoleFor Lock

19Warner Electric • 800-825-9050 P-2012-2PSAC10 Board Dimensions1.31.31.255.753.13J3J46.886.253.13MountingHoles.250 Dia.(7) PlacesJ6J58.25WarnerPart#

2Warner Electric • 800-825-9050 P-2012-2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2System Overview. . . . . . . .

P-2012-2 819-0402 7/05 Printed in USAWarrantyWarner Electric LLC warrants that it will repair or replace (whichever it deems advisable) any produc

3Warner Electric • 800-825-9050 P-2012-2System OverviewThe AC10 Tension Measuring System is designedto measure tension on continuous strip process-ing

4Warner Electric • 800-825-9050 P-2012-2 AC10 TensioncellsAC10 Tensioncells are available in three capaci-ty ranges for non-rotating shaft application

5Warner Electric • 800-825-9050 P-2012-2AC10 ElectronicsThe AC10 microprocessor-based electronicsadds ease of setup, versatility, and accuracy ofthe o

6Warner Electric • 800-825-9050 P-2012-2 SpecificationsAC10 TensioncellsDimensions (I x w x h) . . . . . . . . . . . . . . . . . . . . . . . . . . .

7Warner Electric • 800-825-9050 P-2012-2Pushbutton Key FunctionsThe six pushbutton keys on the PSAC10 board are used to enter and exit the Setup Mode

InstallationPre-Installation InspectionBefore installing the AC10 system:1. Insure all components are present. A typicalsystem consists of two AC10 Te

9Warner Electric • 800-825-9050 P-2012-2Before installing the Tensioncells, refer tomachine drawings, or other documentationto determine the mounting